Flat, Shaped and Round Wire 

Applications 


Cooking Utensils, Food processing and handing components, Chemical processing and handing components, Trim for transportation equipment 

Description 


3000 series of alloys are that are alloyed with manganese. They have higher strength than pure aluminum while maintaining good formability and corrosion resistance. These alloys are not heat treatable and are suitable for anodizing and welding. Alloy 3003 is the most widely used of all the aluminum alloys. 

Chemistry Typical

UNS# A93003 | ALUMINUM | ADDITIONAL ELEMENTS 

1.0-1.5 Mn, 0.05-0.20 Cu, 0.7 Fe max, 0.6 Si max, 0.10 Zn max, 0.05 max other (each), 0.15 max other (total) 


UNS# A93004 | ALUMINUM | ADDITIONAL ELEMENTS 

1.0-1.5 Mn, 1.0-1.3 Mg, 0.25 Cu, 0.70 Fe max, 0.30 Si max, 0.25 Zn max, 0.05 max other (each), 0.15 max other (total) 


UNS# A93105 | ALUMINUM | ADDITIONAL ELEMENTS 

0.20-0.80 Mn, 0.20-0.80 Mg, 0.30 Cu, 0.7 Fe max, 0.6 Si max, 0.40 Zn max, 0.20 Cr max, 0.10 Ti max, 0.05 max other (each), 0.15 max other (total) 

*Contact Ulbrich Wire for request regarding the availability of other aluminum alloys.

Physical Properties

 
Typical Density: 0.0983 - 0.0986 lbs/in3, 2.72 - 2.73 g/cm3

Electrical Conductivity: (% IACS at 68° F, annealed): 40-50% 

Thermal Conductivity: BTU-in/hr-ft2-° F: 
At 68 ° F: 1190 - 1340 

Mean Coefficient of Thermal Expansion: µin/in-°F: 
68 - 572 °F: 13.9 

Modulus of Elasticity: KSI 
10.4 x 103 in tension 

Melting Temperature: 1165 - 1210 °F (629 - 654 °C) 


Forms 

Profile, Round, Flat, Square 

Mechanical Properties at Room Temperature 

Properties: Temper 0 

Ultimate Tensile Strength: 16 KSI min (110 MPa min) 
Yield Strength: 6 KSI min (41.4 MPa min) 
Elongation: 24% min 

Properties: Tempered 

These alloys can be cold worked to various tempers. 

*Actual physical and mechanical properties are alloy dependent. Contact Ulbrich Technical Service for alloy specific properties.

Additional Properties 

Corrosion Resistance 

Contact Ulbrich Wire for specific information. 

Wire Finishes 

XC - Extra clean. Annealed or annealed and cold rolled. Contact Ulbrich Wire with special finish requests. 

Heat Treatment 

These alloys are hardenable by cold working. 

Welding 

Contact Ulbrich Wire for specific information. 

Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the oest of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document. 


Contact Us

Full Name
Title
Company
City, State, Country
Email
Phone (Optional)
Message (Optional)