Grinding Masthead

Finishes & Mechanical Properties

We offer many surface finishes and mechanical properties to reach your desired final product.

Surface Control Capabilities

Surface Control Capabilities

Understanding the work hardening rate of a given alloy or heat lot within an alloy is paramount to achieving the mechanical properties specified by the customer. At Ulbrich, we understand that proper strip temperature control will result in more uniform mechanical properties and grain structure throughout the entire length of a coil. If grains are grown too large, the bulk material may exhibit erratic mechanical properties or an undesirable surface finish. We are able to achieve our desired bright anneal because the entry and exit of the furnace are sealed and the interior is filled with a shielding gas, which aids surface control. The protective atmosphere inside the furnace prevents the formation of excess oxide and allows the strip to retain its rolled finish. Our team of experienced metallurgists will work with you to achieve your final ordered properties.

Datasheets

By Material

View detailed material specifications for the 160+ alloys that Ulbrich supports in strip and wire products.

View Product

Rolled Strip & Slit Coil

ROLLED STRIP & SLIT COIL CAPABILITIES

Finishes

Bright to Dull (10 nanometers – 60 micro-inches), Special Textures can be mechanically (rolled) applied.

Coatings

PVC, Paper Interleaving, Plating and Special Coatings.

View our Special Coatings and Plating Options

Tempers

We engineer our products to each customers requirements and specifications. Our team customized solutions to enhance your product and processes. Our tempers range from drawing quality, coining tempers to extra full hard.

Camber

Camber tolerances are available closer than the published commercial range noted below upon request

For strip less than or equal to 1.5″ wide: .5 inches in 8 feet (less than or equal to 38mm: 13mm in 2.5m)

For strip from 1.5″ – < 24″ wide: 0.25″ in 8 feet (38mm < 610mm: 6mm in 2.5m)

Camber is measured by placing an 8 foot (2.5 meter) straight edge against the concave edge of the strip)

Flatness

Standard flatness is .020 PIW or critical flatness of .010″ PIW (refer to sales for flatness options per material/thickness/width)

Annealing

View our Annealing Capabilities

Grades & Alloys

View our Metal Grades & Alloys

Testing

View our Testing Capabilities

Certifications

View our Certifications

Rolled Wire

WIRE CAPABILITIES

Tempers

Our products can be produced to engineered mechanical properties designed for your end use and manufacturing processes.

Surface Finishes

Custom finished available per customer specifications. Bright Polish, Tin and lead coated, HT and tempered.

Wire Alloys

Stainless Steel – Titanium – Nickel – Cobalt – Nitinol – Carbon Steel – Brass – Bronze – Aluminum – Copper Alloys – Additional Families of Alloys Upon Request

Additional Alloys for Fine Wire and Precision Flat Wire

300 Series VM – Alloy 52 – Aluminum – Aluminum Clad – Beryllium Copper – Brass – Carbon – Copper – Copper Aluminum Clad – Copper Clad – Copper Nickel Alloys – Dumet – Duplex Alloys – FeChrome – Invar – Kovar – L605 – Molybdenum – MP35N – Nickel Alloys – Nickel Plated Steel – Nitinol – Nitronic 32 – Phosphorus Bronze – Stainless Steel – Tantalum -Titanium – Tungsten – More Available Upon Request

View All of Our Metal Grades & Alloy Datasheets

Plating

  • Gold Type I, II, III per MIL-G-45204 Solder per MIL-P 81728*
  • Silver per QQ-S 365 and ASTM B-298 Military Standard – 1276*
  • Copper per MIL-C-14550
  • Nickel per QQ-N-290*
  • Tin per MIL-T-10727 Solder per MIL-STD

Rolled PV Ribbon

PV RIBBON CAPABILITIES

Ulbrich Solar Technologies, a product line of Ulbrich Specialty Wire Products and Ulbrich of Austria, is a global manufacturer and supplier of engineered PV ribbon products. Our solar cell tabbing ribbon and bus wire is custom produced to meet the individual requirements of Solar Module Manufacturers.

For all PV Ribbon and Bus Wire product capabilities please visit our website www.PVRibbon.com

Sheet & Plate

SHEET & PLATE CAPABILITIES

Stainless Steel Sheet (Canada Only)

Alloys: 201, 301, 304, 304L, 309, 316, 316L, 321, 409, 410, 410S, 430, 439

Finishes: 2D, 2B, 4Pol, BA, X10, XL, Buff, XL Blend S, PVC & Paper Interleave

Processing: Shearing to Custom Sizes & Sheet Coil CTL available

Aluminum Sheet (Canada Only)

Alloys: 3003 H14, 5052 H32

Processing: Shearing to custom sizes & Sheet Coil, Cut to length from coil, PVC & Paper Interleave

Stainless Plate Smooth and Diamond Pattern (Canada Only)

Alloys: 201, 201LN, 301, 301LN,304, 304L, 304H, 309S, 310S, 316, 316L, 321, 254SMO, 2205

Processing: Cut to length & Plasma Cutting – Diamond Plate Also Available

* Measurements for general information only. Ultimate capabilities may differ depending on order requirements. Visit www.DiversifiedUlbrich.ca for more information.

Get a Quote

Thanks for your interest in Ulbrich! Whether you're developing a new product or ramping up production, we'll be happy to learn more about your specific needs. Please fill out the form below, and we will promptly get back to you with a quote or, if needed, a request for more information.

  • Product

  • Contact information

  • Request Details

  • Additional criteria and file

Success

Success!

Thank you!

Form submitted successfully. Someone from Ulbrich will be in-touch with you soon.

GETTING STARTED

Which product or service are you interested in?

To ensure your request gets routed to the right Ulbrich team, let us know which
metal product, or service you're looking to source.