Grade 5 Titanium (Ti-6Al-4V) UNS R56400

Ti 6-4 (Grade 5) is significantly stronger than commercially pure titanium while having the same stiffness and thermal properties (excluding thermal conductivity, which is about 60% lower in Grade 5 than in CP Ti).

Full Name
Email
Company
Business Address

Grade 5 Titanium (Ti-6Al-4V) Strip*, Coil*, Foil*, Wire, ASTM B265

Description

Ti 6-4 (Grade 5) is significantly stronger than commercially pure titanium while having the same stiffness and thermal properties (excluding thermal conductivity, which is about 60% lower in Grade 5 than in CP Ti). Among its many advantages, Grade 5 Titanium it is heat treatable. This grade is an excellent combination of strength, corrosion resistance, weldability and fabricability.

Applications

Chemistry Typical

Titanium: Balance
Vanadium: 4.0
Aluminum: 6.0
Hydrogen: 0.015 max
Nitrogen: 0.02 max
Carbon: 0.10 max
Iron: 0.25 max
Residual each: 0.10 max., total 0.40 max

Common Titanium Grade Names

Name

Code

Description 1Description 2ASTMAMSUNS
Grade 5 Titanium6-4Titanium Alloy 6% Aluminum, 4% VanadiumR56400



Physical Properties of Ti-6Al-4V

Density: 0.16 lbs/in3, 4.43 g/cm3

Mean Coefficient of Thermal Expansion: in/in/° F (mm/ml° C):
70 - 212 °F (20 - 100 ° C): 4.78 x 10-6 (8.6)

Thermal Conductivity: BTU-in/h-ft-°F (W/m-°K):
At 70 °F (21 °C): 46.5 (6.7)

Modulus of Elasticity: ksi (MPa)
16.5 x 103 (113.8 x 103) in tension

Melting Point: 3020 °F (1660 °C)

Forms

Coil
  • Strip
  • Foil
  • Ribbon

Wire
  • Shaped Wire

Mechanical Properties at Room Temperature

Properties: Annealed (Typical)

Ultimate Tensile Strength: 135 KSI (950 MPa)
Yield Strength (0.2% offset): 125 KSI (880 MPa)
Elongation: 15%
Hardness: Re 34

Properties: Tempered

Ti 6-4 (Grade 5) can be cold rolled to various tempers. Contact Ulbrich Technical Service for additional information.

Additional Properties

Corrosion Resistance

Refer to NACE (National Associate of Corrosion Engineers) for recommendations.

Finishes

Strip, Foil, Ribbon: Inquire with Ulbrich Stainless Steel Wire: Inquire with Ulbrich Wire

Heat Treatment

Ti 6-4 (Grade 5) can only be hardened by cold work.

Welding

For best results refer to: SSINA's "Welding of Stainless Steels and Other Joining Methods".

Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document.

success Your information has been submitted successfully and an Ulbrich specialist will be in touch with you soon.

Contact Us

Full Name
  • ${ error }
Email
  • ${ error }
Company
  • ${ error }
Title
Business Address
  • ${ error }
Phone
Message