Hastelloy® C-22 UNS N06022
Hastelloy® C-22 is a most versatile nickel-chromium-molybdenum-tungsten alloy with improved resistance to both uniform and localized corrosion as well to a wide variety of mixed industrial chemicals.
(Nickel Alloy HC22) Strip, Foil, Wire, ASTM B575
Bellows, flue gas scrubber components, nuclear fuel reprocessing and sour gas production
Hastelloy® C-22 is a most versatile nickel-chromium-molybdenum-tungsten alloy with improved resistance to both uniform and localized corrosion as well to a wide variety of mixed industrial chemicals. HC-22 has corrosion resistance superior to other Ni-Cr-Mo alloys including C-276, C-4 and 625. The C-22 alloy exhibits superior weldability.
Chromium: 20.00 - 22.50
Molybdenum: 12.50 - 14.50
Iron: 2.00 - 6.00
Tungsten: 2.50 - 3.00
Cobalt: 2.50 max
Carbon: 0.10 max
Silicon: 0.08 max
Manganese: 0.50 max
Phosphorus: 0.02 max
Vanadium: 0.35 max
Density: 0.314 lbs/in3, 8.69 g/cm3
Mean Coefficient of Thermal Expansion: in/in/° F (mm/m/°C):
70 - 212 °F (20 - 100 °C): 6.9 x 10-5 (12.4)
Thermal Conductivity: BTU- in/h-ft- (W/m- °K):
70 °F (21 °C): 70 (10.1)
Modulus of Elasticity: ksi (MPa)
29.9 x 103 (206 x 103) in tension
Melting Point: 2550 °F (1400 °C)
Coil - Strip, Foil, Ribbon Wire - Profile, Round, Flat, Square
Mechanical Properties at Room Temperature
Ultimate Tensile Strength: 100 KSI min (690 MPa min)
Yield Strength: (0.2% offset) 45 KSI min (310 MPa min)
Elongation: 45% min
Hardness: Rb 100 max (aim)
Hastelloy® C-22 can be cold rolled to various tempers. Contact Ulbrich Technical Service for additional information.
Refer to NACE (National Associate of Corrosion Engineers) for recommendations.
#1 - Hot rolled annealed and descaled. It is available in strip, foil and ribbon. It is used for applications where a smooth decorative finish is not required.
#2D - Dull finish produced by cold rolling, annealing and descaling. Used for deep drawn parts and those parts that need to retain lubricants in the forming process. #2B - Smooth finish produced by cold rolling, annealing and descaling. A light cold rolling pass is added after anneal with polished rolls giving it a brighter finish than 2D.
#BA- Bright annealed cold rolled and bright annealed
#CBA- Course bright annealed cold rolled matte finish and bright anneal
#2 - Cold Rolled #2BA- Smooth finish produced by cold rolling and bright annealing. A light pass using highly polished rolls produces a glossy finish. A 2BA finish may be used for lightly formed applications where a glossy finish is desired in the formed part. Polished - Various grit finish for specific polish finished requirements.
* Not all finishes are available in all alloys - Contact Ulbrich Sales for more information.
XC - Extra Clean Bright Annealed or Bright Annealed and Cold Rolled Grease - Ultra bright finish (for decorative applications) Soap - Soap coating on tempered wire to act as lubricant. * Contact Ulbrich Wire for custom wire finishes
Hastelloy® C-22 cannot be hardened heat treating.
For best results refer to: SSINA's "Welding of Stainless Steels and Other Joining Methods".
Hastelloy® C-22 is a grade of Hastelloy® which is a nickel-molybdenum alloy. There are many different grades of Hastelloy®, which includes C-22. Grades of Hastelloy® have each been optimized for a specific purpose. Molybdenum makes Hastelloy® harder and stronger at high temperatures. This alloying element and the characteristics it imbues into the material also makes it great for welding applications. These nickel alloys are easily fabricated and formed. They also exhibit good ductility and are able to be cold worked.
All grades of Hastelloy® are considered to be a corrosion resistant alloy because each grade exhibits superior resistance to various corrosive environments. Hastelloy® has outstanding resistance to highly oxidizing corrosives such as oxidizing salts and reducing agents, making it a great alloy to specify for applications used in moderate to severe corrosive environments.
Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document.