Niobium Type 1 & 2 Wire UNS R04300 UNS R04210

Niobium is a very soft refractory metal with an extremely high melting point and corrosive resistant properties.

Full Name
Email
Company
Business Address

Strip, Coil, Foil, Wire, ASTM B393

NIOB1 (Type 1 Reactor Grade Unalloyed)
NIOB2 (Type 2 Commercial Grade Unalloyed)

Applications

Type 1 and Type 2:

Used in jewelry, super-abrasives, thin film deposition (glass), high-energy physics, springs and superconducting magnets for aerospace, consumer electronics, medical and superconducting applications.

Description

Niobium is a very soft refractory metal with an extremely high melting point and corrosive resistant properties. High thermal/electric conductivity, easily fabricated and bio-compatible.

Chemistry: Ingot

Element Niobium | Type 1 Reactor Grade Balance | Type 2 Commercial Grade Balance

Element Carbon | Type 1 Reactor Grade 0.01 | Type 2 Commercial Grade 0.01

Element Nitrogen | Type 1 Reactor Grade 0.01 | Type 2 Commercial Grade 0.01

Element Oxygen | Type 1 Reactor Grade 0.015 | Type 2 Commercial Grade 0.025

Element Hydrogen | Type 1 Reactor Grade 0.0015 | Type 2 Commercial Grade 0.0015

Element Zirconium | Type 1 Reactor Grade 0.02 | Type 2 Commercial Grade 0.02

Element Tantalum | Type 1 Reactor Grade 0.1 | Type 2 Commercial Grade 0.3

Element Iron | Type 1 Reactor Grade 0.005 | Type 2 Commercial Grade 0.005

Element Silicon | Type 1 Reactor Grade 0.005 | Type 2 Commercial Grade 0.005

Element Tungsten | Type 1 Reactor Grade 0.03 | Type 2 Commercial Grade 0.05

Element Nickel | Type 1 Reactor Grade 0.005 | Type 2 Commercial Grade 0.005

Element Molybdenum | Type 1 Reactor Grade 0.020 | Type 2 Commercial Grade 0.020

Element Hafnium | Type 1 Reactor Grade 0.02 | Type 2 Commercial Grade 0.02

Element Titanium | Type 1 Reactor Grade 0.02 | Type 2 Commercial Grad 0.02

Below Elements When Specified:

Boron - 2ppm

Aluminum - 0.002 - 0.005

Beryllium - 0.005

Chromium - 0.002

Cobalt - 0.002


Physical Properties

Density: 0.310 lbs/in3, 8.66 g/cm3

Mean Coefficient of Thermal Expansion, in/in/° F (mm/m/° C)
70 - 212 °F (20 - 100 ° C): 4.05 x 10-6 (7.3)

Thermal Conductivity: (W/m-° K)
(21 ° C): 53.7

Modulus of Elasticity, ksi (MPa)
1.52 x 103 (104.9 x 103) in tension

Melting Point: 4490 ° F (2477 ° C)

Forms

Coil - Strip, Foil, Ribbon
Wire - Profile, Round, Flat, Square

Mechanical Properties at Room Temperature

Annealed: Typical

Ultimate Tensile Strength: 18 KSI min (124 MPa min)
Yield Strength (0.2% offset): 10.5 KSI min (72 MPa min)
Elongation:
Gauges: less than 0.010 inches: 15% min
Gauges: 0.010 inches and greater: 20% min

*Niobium Type 1 and Type 2 can be cold rolled to various tempers. Contact Ulbrich Technical Service for additional information.

Additional Properties

Corrosion Resistance

Refer to NACE (National Associate of Corrosion Engineers) for recommendations.

Finishes

#1 - Hot rolled annealed and descaled. It is available in strip, foil and ribbon. It is used for applications where a smooth decorative finish is not required.
#2D - Dull finish produced by cold rolling, annealing and descaling. Used for deep drawn parts and those parts that need to retain lubricants in the forming process.
#2B - Smooth finish produced by cold rolling, annealing and descaling. A light cold rolling pass is added after anneal with polished rolls giving it a brighter finish than 2D.
#BA- Bright annealed cold rolled and bright annealed
#CBA- Course bright annealed cold rolled matte finish and bright anneal
#2 - Cold Rolled
#2BA- Smooth finish produced by cold rolling and bright annealing. A light pass using highly polished rolls produces a glossy finish. A 2BA finish may be used for lightly formed applications where a glossy finish is desired in the formed part.
Polished - Various grit finish for specific polish finished requirements.

*Not all finishes are available in all alloys - Contact Ulbrich Sales for more information.

Wire Finishes

XC - Extra clean. Bright annealed or bright annealed and cold rolled Grease - Ultra bright finish for decorative applications

Soap - Soap is not removed from tempered wire to act as a lubricant.

*Contact Ulbrich Wire for custom finishes.

Heat Treatment

Niobium Type 1 and Type 2 are non hardenable by heat treatment. They can only be hardened by cold working.

Welding

For best results refer to: SSINA's "Welding of Stainless Steels and Other Joining Methods".


Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document.



Get a Quote

Thanks for your interest in Ulbrich! Whether you're developing a new product or ramping up production, we'll be happy to learn more about your specific needs. Please fill out the form below, and we will promptly get back to you with a quote or, if needed, a request for more information.

  • Product

  • Contact information

  • Request Details

  • Additional criteria and file

Success

Success!

Thank you!

Form submitted successfully. Someone from Ulbrich will be in-touch with you soon.

GETTING STARTED

Which product or service are you interested in?

To ensure your request gets routed to the right Ulbrich team, let us know which
metal product, or service you're looking to source.