Flat, Shaped and Round Wire  ASTM B152, ASTM B747, QQ-C-576


Electrical/electronic and solar applications where strength is not required. Additional applications are downspouts, gutters, roofing, gaskets, heat sinks, busbars, nails, printing rolls, rivets, etc. parts. 


In general, copper alloys exhibit good to excellent corrosion resistance and high thermal conductivity and very high electrical conductivity. Pure copper's electrical conductivity is so high that many metals are measured against it in the form of the IACS (International Annealed Copper Standard). 

Chemistry Typical 


C10100     99.99 min    0.0005 max                                               0.0005 max  

C10200     99.95 min    0.001 max                           0.0003 max  

C10400     99.95 min    0.001 max      0.027 min  

C10500     99.95 min    0.001 max      0.034 min  

C10700     99.95 min    0.001 max      0.085 min  

C11000     99.90 min  

C12000     99.90 min                                            0.004-0.012 

C12100     99.90 min                         0.014           0.004-0.012 

C15000     Balance*                                                                       0.10-0.20 Zr 

C15500     99.75 min                         0.027-0.10   0 .040-0 .080    0.08-0.13 Mg 

* Contact Ulbrich Wire for request regarding the availability of other copper alloys.

* Contact Ulbrich Technical Department for limits for additional trace elements and impurity levels. * Copper Values include Silver. * Copper plus named elements.

Typical Density: 0.332 lbs/in3, 8.92 g/cm3

Electrical Conductivity:(% IACS at 68° F 20°C, annealed): 85-101% 

Specific Heat: BTU/lb-° F (J/g-°C): 0.0920 (0.385) 

Mean Coefficient of Thermal Expansion: µin/in-° F (µm/m-°C)  68 - 572 °F (20 - 300 °C): 9.8 (17.6) 

Thermal Conductivity: BTU-in/hr-ft2-° F (W/m•K): 2712 (390.8) 

Modulus of Elasticity: KSI (MPa)  17 x 103 in tension 

Melting Range: 1981 °F (1083 °C) 


Profile, Round, Flat, Square 

Mechanical Properties at Room Temperature 

Properties: Annealed Typical 

Ultimate Tensile Strength: 26 - 38 KSI (179 - 262 MPa) Yield Strength: 10 KSI (69 MPa) Nominal 

Elongation: 35% 

Properties: Tempered 

Copper alloys can be cold worked to various tempers. 

*Actual physical and mechanical properties are alloy dependent. Contact Ulbrich Technical Service for alloy specific properties.

Additional Properties 

Corrosion Resistance  

Contact Ulbrich Wire for specific information. 

Wire Finishes  

XC - Extra clean. Annealed or annealed and cold rolled. Contact Ulbrich Wire with special finish requests. 

Heat Treatment 

Copper alloys are non hardenable by heat treatment. 


Contact Ulbrich Wire for specific information. 

Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document. 

Contact Us

Full Name
City, State, Country
Phone (Optional)
Message (Optional)