Nickel 201 Wire UNS N02201

Nickel 201 is a commercially pure nickel that provides highly ductile mechanical properties across a wide temperature range, and corrosion resistance in neutral to moderately reducing environments.

Full Name
Email
Company
Business Address

Shaped, Flat, Square, Round, Fine Wire, Plated and Un-plated ASTM B162

Nickel 201 Wire Description


Nickel 201 is a commercially pure nickel with a maximum carbon level of 0.02%. This alloy provides highly ductile mechanical properties across a wide temperature range, and corrosion resistance in neutral to moderately reducing environments. It provides high thermal and electrical conductivity in comparison to nickel-base alloys, stainless and low alloy steels. With its lower carbon content, alloy 201 may be considered for service above 600°F (316°C), where alloy 200 with higher carbon content is not recommended.

Applications


Applications requiring excellent corrosion resistance and strong magnetic properties.

Lead wires

Battery components
Transducers
Sparking electrodes
Heat exchangers

Chemistry Typical


Nickel + Cobalt: 99.99 min
Carbon: 0.02 max
Manganese: 0.35 max
Silicon: 0.35 max
Sulfur: 0.010 max
Iron: 0.40 max
Copper: 0.25 max

Physical Properties


Density: 0.322 lbs/in³, 8.90 g/cm³

Thermal Conductivity, BTU/hr/ft²/ft/°F (W/m•K)
212ºF (100ºC): 38.8(67.1)
400°F (204°C): 35.4(61.3)
600ºF (316ºC): 36.5(56.3)

Mean Coefficient of Thermal Expansion, in/in/°F (μm/m•K)
80-200°F (27-93°C): 7.4 x 10 (13.3)
80-400°F (27-204°C): 7.7x 10 (13.9)
80-600°F (27-316°C): 8.0x 10 (14.4)

Modulus of Elasticity KSI (MPa)
30.0x 10³ (207 x 10³)

Melting Range: 2615-2535°F(1435-1445°C)

Mechanical Properties at Room Temperature

Properties: Annealed

Ultimate Tensile Strength: 50 KSI min (345 MPa min)
Yield Strength (0.2% offset): 12 KSI min (83 MPa min)
Elongation:
30% min: gauges < 0.050 inches
35% min: gauges ≥ 0.050 inches
Hardness:
HV 117 max: gauges ≤ 0.010 inches
Rb 66 max: gauges > 0.010 inches


Properties Tempered




Alloy 201 can be cold rolled to achieve the temper properties required by specific customers and/or manufacturing requirements. Contact Ulbrich Wire for details.

Additional Properties


Corrosion Resistance


Alloy 201 is used principally in reducing or neutral environments. It may also be used in oxidizing environments that cause the formation of a passive film. The nickel content of this alloy renders it virtually immune to chloride stress corrosion cracking. It can also be used in fresh and many other process waters. Sulfurous atmospheres are corrosive to Nickel alloys.

Refer to NACE (National Association of Corrosion Engineers) for recommendations.

Standard Wire Finishes


Extra Clean: (XC) Extra clean is also referred to as “bright annealed” or “bright annealed and cold rolled”

Grease (round wire only): Drawn in a heavy grease produces an “Ultra bright” finish for decorative applications.

Soap (round wire only): Soap is used as a lubricant in the drawing process and is not removed. It acts as a lubricant during customer part forming operation.

A soap finish is available in tempered products.
Plated: Many plating options are available.
*Special finishes are available: Contact Ulbrich Wire Sales with special finish and plating requests.

Forms


Continuous Coils
Cut to lengths
Precision cutting

Heat Treatment


Alloy 201 is non hardenable by heat treatment.

Welding


For best results refer to: SSINA’s “Welding of Stainless Steels and Other Joining Methods”

Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels and Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the ‘applications’ noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document.

Get a Quote

Thanks for your interest in Ulbrich! Whether you're developing a new product or ramping up production, we'll be happy to learn more about your specific needs. Please fill out the form below, and we will promptly get back to you with a quote or, if needed, a request for more information.

  • Product

  • Contact information

  • Request Details

  • Additional criteria and file

Success

Success!

Thank you!

Form submitted successfully. Someone from Ulbrich will be in-touch with you soon.

GETTING STARTED

Which product or service are you interested in?

To ensure your request gets routed to the right Ulbrich team, let us know which
metal product, or service you're looking to source.