(Alloy G-3) Strip, Coil, Foil & Wire, ASTM 582, ASTM B 581 

Applications

  Hastelloy® G-3 is used in handling equipment that processes reducing acids such as phosphoric and sulfuric. Other applications are scrubbers, sour gas and oil production equipment. 

Description 

Hastelloy® G-3 is nickel-chromium-iron alloy with addition of molybdenum and copper. The alloy has excellent corrosion resistance to oxidizing chemicals and atmospheres while offering resistance to reducing chemical resulting from the nickel and copper content. 

Chemistry Typical 

Nickel: Balance 
Chromium: 21.00-23.5 
Iron: 18.00-21.00 
Molybdenum: 6.0-8.0 
Copper: 1.5-2.5 
Cobalt: 5.0 max 
Columbium + Tantalum: 0.50 max 
Carbon: 0.015 max  Tungsten: 1.5 max 
Silicon: 1.0 max 
Phosphorus: 0.04 max 
Sulfur: 0.03 max 

Physical Properties 

Density: 0.294 lb/in3, 8.14 g/cm3 Electrical Resistivity: ohm-cir-mil/ft,(micro-ohms-cm):  675.97(112.37) 

Specific Heat: BTU/lb-°F (J/Kg-°C) 
At 77 °F (25 °C): 0.108 (453) 
At 212 °F (100 °C): 0.111 (464) 
At 392 °F (200 °C): 0.114 (478) 
At 572 °F (300 °C): 0.118 (493) 
At 752 °F (400 °C): 0.121 (507) 
At 932 °F (500 °C): 0.124 (521) 
At 1112 °F (600 °C): 0.130 (543) 

Thermal Conductivity: BTU-in/hr-ft2-°F, (W/m-°C) 
At 77 °F (25 °C): 69 (10.0) 
At 212 °F (100 °C): 82 (11.8) 
At 392 °F (200 °C): 96 (13.8) 
At 572 °F (300 °C): 110 (15.9) 
At 752 °F (400 °C): 124 (17.9) 
At 932 °F (500 °C): 139 (20.0) 
At 1112 °F (600 °C): 151 (21.8) 

Mean Coefficient of Thermal Expansion: µin/in-°F (µm/m-°C) 

75-212 °F (24 -100 °C): 8.1 (14.6) 
75-392 °F (24 -200 °C): 8.1 (14.6) 
75-572 °F (24 -300 °C): 8.1 (14.6) 
75 -752 °F (24 -400 °C): 8.2 (14.8) 
75 -932 °F (24 -500 °C): 8.4 (15.1) 
75-1112 °F (24-600 °C): 8.4 (15.1)

Modulus of Elasticity: ksi (MPa) 
28.9 x 103 (199 x 103) in tension 

Melting Range: 2300 - 2450 °F (1260 - 1343 °C) 

Forms 

Coil -Sheet, Strip, Foil  Wire -Profile, Round, Flat, Square 

Mechanical Properties at Room Temperature 

Properties: Annealed Typical 

Ultimate Tensile Strength: 90 KSI min (621 MPa min) 
Yield Strength: 35 KSI min (241 MPa min) 
Elongation: 45% min 
Hardness: aim Rb 100 max 

Properties: Tempered

Hastelloy® G-3 can be cold worked to various tempers. Contact Ulbrich Technical Service for additional information. 

Additional Properties

Corrosion Resistance

Refer to NACE (National Associate of Corrosion Engineers) for recommendations. 

Finishes

#1 - Hot rolled annealed and descaled. It is available in strip, foil and ribbon. It is used for applications where a smooth decorative finish is not required. 
#2D - Dull finish produced by cold rolling, annealing and descaling. Used for deep drawn parts and those parts that need to retain lubricants in the forming process.  #2B - Smooth finish produced by cold rolling, annealing and descaling. A light cold rolling pass is added after anneal with polished rolls giving it a brighter finish than 2D. 
#BA - Bright annealed cold rolled and bright annealed 
#CBA - Course bright annealed cold rolled matte finish and bright anneal 
#2 - Cold Rolled 
#2BA- Smooth finish produced by cold rolling and bright annealing. A light pass using highly polished rolls produces a glossy finish. A 2BA finish may be used for lightly formed applications where a glossy finish is desired in the formed part.  Polished - Various grit finish for specific polish finished requirements. 

* Not all finishes are available for all alloys - Consult sales for applicable finishes.

Wire Finishes

XC - Extra Clean Bright Annealed or Bright Annealed and Cold Rolled Grease - Ultra bright finish (for decorative applications)  Soap - Soap coating on tempered wire to act as lubricant.  * Contact Ulbrich Wire with special finish requests.

Heat Treatment

Hastelloy® G-3 is non hardenable by heat treatment.

Welding

For best results refer to: SSINA's "Welding of Stainless Steels and Other Joining Methods". 




Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document.

 

Contact Us

Full Name
Title
Company
City, State, Country
Email
Phone (Optional)
Message (Optional)