Strip, Coil, Foil, Wire, AMS 5525, AMS 5858 

Applications 

Jet engine applications, low temperature applications 

Description 

Type A286 is an iron base superalloy useful for applications requiring high strength and corrosion resistance up to 1300 °F (704 °C) and for lower stress applications at higher temperatures. The alloy is also used for low temperature applications requiring a ductile, non-magnetic high strength material at temperatures ranging from above room temperature down to at least -320 °F (-196 °C). 

Chemistry Typical 

Carbon: 0.080 max 
Manganese: 2.00 max 
Silicon: 1.00 max 
Chromium: 13.50-16.00 
Nickel: 24.00-27.00 
Titanium: 1.90-2.35 
Molybdenum: 1.00-1.50 
Vanadium: 0.10-0.50 
Boron: 0.003-0.010 
Cobalt: 1.00 max 
Aluminum: 0.35 max 
Phosphorus: 0.02 max 
Sulfur: 0.025 max. 
Iron: Balance 

Physical Properties 

Density: 0.286 lbs/in3 7.92 g/cm3

Thermal Conductivity: BTU/hr/ft2/ft/°F (W/m•K): 
At 302 °F (150 °C): 8.7 (15.1) 
At 572 °F (300 °C): 10.3 (17.8) 
At 932 °F (500 °C): 12.6 (21.8) 
At 1112 °F (600 °C): 13.8 (23.9) 

Mean Coefficient of Thermal Expansion: in/inl°F (µm/m•K)
70 - 200 °F (21 - 93 °C): 9.17 x 10-5 (16.5) 
70 - 600 °F (21 - 315 °C): 9.47 x 10-5 (17.0) 
70 - 800 °F (21 - 427 °C): 9.64 x 10-5 (17.4)
70 - 1000 °F (21 - 538 °C): 9.78 x 10-5 (17.6) 

Modulus of Elasticity: ksi (MPa)  29.1 x 103 (201 x 103) in tension 

Forms 

Coil - Strip, Foil, Ribbon  Wire - Profile, Round, Flat, Square 

Mechanical Properties at Room Temperature 

Properties: Annealed 

Ultimate Tensile Strength: 105 KSI max (724 MPa max)

Elongation: 

10% min: Gauge: .001 - .0015 
12% min: Gauge .0015 - .002 
20% min: Gauge .002 - .004 
25% min: Gauge > .004 

Hardness: Rb 90 max 

Properties: Tempered

Consult Ulbrich Technical Services if temper rolled properties are needed. 

Properties: Stress Rupture (Typical) 

A stress of 67 .5 KSI min for no less than 23 hours. 

Heat Treat Capabilities: Typical

Ultimate Tensile Strength: 
125 KSI min (862 MPA min): Gauge: .001 - .0015 
130 KSI min (896 MPA min): Gauge .0015 - .002 
135 KSI min (931 MPA min): Gauge .002 - .004 
140 KSI min (965 MPA min): Gauge> .004 

Elongation:
4% min: Gauge: .001 - .0015 
8% min: Gauge .0015 - .002 
10% min: Gauge .002 - .004 
15% min: Gauge > .004 

Additional Properties

Corrosion Resistance

Refer to NACE (National Association of Corrosion Engineers) for recommendations. 

Finishes

# 1 - Hot rolled annealed and descaled. It is available in strip, foil and ribbon. It is used for applications where a smooth decorative finish is not required. 
# 2D - Dull finish produced by cold rolling, annealing and descaling. Used for deep drawn parts and those parts that need to retain lubricants in the forming process.  # 2B - Smooth finish produced by cold rolling, annealing and descaling. A light cold rolling pass is added after anneal with polished rolls giving it a brighter finish than 2D. 
#BA - Bright annealed cold rolled and bright annealed 
#CBA - Course bright annealed cold rolled matte finish and bright anneal 
#2 - Cold Rolled 
# 2BA- Smooth finish produced by cold rolling and bright annealing. A light pass using highly polished rolls produces a glossy finish. A 2BA finish may be used for lightly formed applications where a glossy finish is desired in the formed part.  Polished - Various grit finish for specific polish finished requirements. 
* Not all finishes are available for all alloys - Please contact Ulbrich sales for more information.

Wire Finishes

XC - Extra clean bright annealed or bright annealed and cold rolled Grease - Ultra-bright finish (for decorative applications)  Soap - Soap is not removed from tempered wire to act as a lubricant.  * Contact Ulbrich Wire with special wire finishes. 

Welding

For best results refer to: SSINA's "Welding of Stainless Steels and Other Joining Methods".




Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document. 

 

Contact Us

Full Name
Title
Company
City, State, Country
Email
Phone (Optional)
Message (Optional)