Strip, Coil, Foil & Wire, AMS 5523, ASTM A167 

Applications 

Furnace parts, Heat Exchangers, Paper Mills

Description     

Type 309 is an austenitic chromium nickel stainless steel (.08% max carbon). Type 309 is employed for parts requiring both corrosion and heat resistance and oxidation resistance up to 2000 °F. Strength at elevated temperatures is similar to that of 18-8 Stainless Steels. This alloy posses excellent resistance to oxidation as well as high tensile and creep strengths at elevated temperatures. It is more resistant to marine atmospheres than Type 304. It is generally considered as a heat-resisting alloy. 

Chemistry Typical    

Carbon: 0.08 max 
Manganese: 2.00 max 
Silicon: 1.00 max 
Chromium: 22.00- 24.00 
Nickel: 12.00- 15.00 
Molybdenum: 0.75 max 
Phosphorus: 0.040 max   
Sulphur: 0.030 max 
Copper: 0.75 max 
Iron: Balance 

Physical Properties

Density: 0.289 lbs/in3 9.01 g/cm3

Electrical Resistivity: microhm-in (microhm-cm):  68 °F (20 °C): 30.7 (78.0) 

Specific Heat: BTU/lb/°F (kJ/kg•K): 
32 - 212 °F (0 - 100 °C): 0.12 (0.50) 

Thermal Conductivity: BTU/hr/ft2/ft/° F, (W/m•K) 
At 212 ° F (100 °C)-9.0 (15.6) 
At 932 ° F (500 °C)-10.8 (18.7) 

Mean Coefficient of Thermal Expansion: in/in/°F (µm/m•K) 
32 -212 °F (0 -100 °C)-8.3 x 10-6 (14.9) 
32 -600 °F (0-315 °C)-9.3 x 10-6 (16.7) 
32-1000 °F (0-538 °C)-9.6 x 10-6 (17.3)
32 -1200 °F (0 -649 °C)-10.0 x 10-6 (18.0)

Modulus of Elasticity: ksi (MPa) 
29 x 103 (200 x 103) in tension 
11.2 x 103 ( 78 x 103) in torsion 

Magnetic Permeability, H = 200 Oersteds: Annealed < 1.02 max. 

Melting Range: 2550 - 2590 ° F (1399 - 1454 °C) 

Forms

Coil -Strip, Foil, Ribbon  Wire -Profile, Round, Flat, Square 

Mechanical Properties at Room Temperature  Properties: Typical   

Ultimate Tensile Strength: 75 KSI min (620 MPa min) Yield Strength (0.2% Offset): 30 KSI min (205 MPa min) Elongation: 40% min  Hardness: Rb 95 max 

Tempered

309 can be supplied in a rolled tempered condition. Contact Ulbrich Technical Service for details. 

Additional Properties

Corrosion Resistance  

Refer to NACE (National Association of Corrosion Engineers) for recommendations. 

Finishes   

# 1 - Hot rolled annealed and descaled. It is available in strip, foil and ribbon. It is used for applications where a smooth decorative finish is not required.  # 2D - Dull finish produced by cold rolling, annealing and descaling. Used for deep drawn parts and those parts that need to retain lubricants in the forming process.  # 2B - Smooth finish produced by cold rolling, annealing and descaling. A light cold rolling pass is added after anneal with polished rolls giving it a brighter finish than 2D.  #BA- Bright annealed cold rolled and bright annealed  #CBA- Course bright annealed cold rolled matte finish and bright anneal  #2 - Cold Rolled  # 2BA- Smooth finish produced by cold rolling and bright annealing. A light pass using highly polished rolls produces a glossy finish. A 2BA finish may be used for lightly formed applications where a glossy finish is desired in the formed part.  Polished - Various grit finish for specific polish finished requirements.  * Not all finishes are available for all alloys - Contact Ulbrich Sales for more information.

Wire Finishes  

XC - Extra clean bright annealed or bright annealed and cold rolled Grease - Ultra-bright finish (for decorative applications)  Soap - Soap coating on tempered wire to act as lubricant.  * Contact Ulbrich Wire for custom wire finishes.

Cold Forming    

Type 309 can be rolled formed, stamped and drawn readily. In-process annealing is usually required to reduce hardness and increase ductility. 

Heat Treatment         

Type 309 can only be hardened by cold working. 

Welding         

For best results refer to: SSINA's "Welding of Stainless Steels and Other Joining Methods".

Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document. 

Contact Us

Full Name
Title
Company
City, State, Country
Email
Phone (Optional)
Message (Optional)